shortqert.blogg.se

1. #Ball joint rivet removal tool install#
2. #Ball joint rivet removal tool professional#
3. #Ball joint rivet removal tool free#

Even a few tenths of a degree can cause tire wear and handling problems. Now it’s off for a test drive! Don’t forget to take your vehicle to a shop for an alignment after any major steering or suspension work like this. The left was completely destroyed! To see how these destroyed ball joints damaged the control arm, check out this article I wrote a while back.īolt the new ball joint in with the included hardware, torque to specs (you do have a torque wrench don’t you?), and reassemble the rest. Here’s what the lower ball joints looked like once they were removed. I used a 2″ die grinder with a sanding disc. Once you get the ball joints out, be sure to clean the mating surface so the ball joint seats completely and fits tightly against the control arm. Go just deep enough to weaken the head of the rivet enough to punch it out with an air chisel or a regular punch. for loosening tightly fitted ball joints turning of ball joint with this tool facilitates dismounting suitable for Audi A4, A5, A6, A7, Q5 27 mm hexagon. You don’t want to go too far or the control arm will be damaged. Any ball joint rivet removal instructions Ive ever seen say to. I used a scrap 2X4 to hold the upper control arm up where I could get to it and commenced to drilling! These are from the lower control arm, but I wanted to show you about how deep to drill. Well try some more today with the air tools. Using a 1/2' drill, drill just deep enough to remove rivet head. You can imagine that after 15-20 years or more the rivets are pretty stuck in there. SPECIAL TOOLS Ball joint pressing tools The following are typical steps that apply to. I suppose it was a bit cheaper and/or easier for GM to use rivets instead of bolts for these, but it sure would have been nice to take a few bolts loose rather than deal with these things. These guys are the pesky rivets that we’re drilling out. I’ll do an article on that method, too, because that’s how I replaced Henry’s ball joints. If you choose to cut the rivets off, I recommend using a cut off wheel or similar tool to cut an X in the rivet head (shown) to make it a little easier. You can use an air chisel (or a standard old chisel if you’re a glutton for punishment or Paul Bunyan with a hammer) to cut the head of the rivets off in the direction of the red arrow, grind off the rivet heads, or drill them out. Once you get to this point you have some options. It’s a good idea to secure the brake caliper with a ratchet strap, bungee cord, or my new favorite, a Ratchet Rope so the hose won’t be damaged if it falls during your copious beating, banging, drilling, etc. Orion Motor Tech Ball Joint Press Kit, 10pc Ball Joint Removal Tool for Brake Anchor Pin, U Joint Removal Tool with C Frame & 4x4 Adapters, Ball Joint Removing Tool for Most 2WD 4WD Cars Light Trucks. By the way, I haven’t had very good luck with the pickle fork kits with interchangeable heads, so I would recommend getting a dedicated set. On this 2001 Chevy S10 4×4 I was able to leave the brakes in tact and remove just the ball joints using a pickle fork unfortunately you won’t be so lucky on every vehicle out there.

#Ball joint rivet removal tool free#

Let’s get dirty!įirst, you’ll want to get the control arms free from the steering knuckle.

This post will cover my preferred method of replacing riveted ball joints specifically. This puller can be used on almost any Polaris ATV or UTV with the strut style front suspension from about 1985 to current.If you’re up to replacing these riveted ball joints I’ll assume you feel comfortable removing the components necessary to get to the ball joints. Does the balljoint spin freely or slop up and down in its housing? No problem, this puller will easily remove it! Complete instructions are included. If your threads are damaged, those other pullers will not work! Even in your threads are damaged you can normally still make our puller work due to the dual puller design.

Unlike other tools on the market that use all of the old ball joints threads, this tool only uses the top few threads of the ball joint.

#Ball joint rivet removal tool professional#

The heavy duty design is suited for either home or professional shop use.

#Ball joint rivet removal tool install#

This two piece steel puller simply goes over the balljoint, install the nut, and turn out the inner puller to remove the ball joint. We developed this unique tool to make the job much easier. Pulling the ball joints from the aluminum strut housing on most Polaris ATV’s can be a real challenge.